Palfinger Walvoil DPX 100 + Scanreco G3 with Otto Joystick

Hydraulic Valve Walvoil DPX 100 12/24V with 8 Proportional Sections, Open/Closed Center, and Additional Levers. The valve includes a post-compensation section.

Scanreco G3 Canbus system equipped with Otto Joysticks 12/24V.

This kit is configured for the most popular machine settings, supporting up to 8 standard forest crane functions. If you require a different dedicated configuration, we can customize it to meet your needs, including variations in spools, voltage, the number of sections, anti-shock valves, connectors, etc.

The kit is designed for plug-and-play convenience. We handle everything from the plugs to the software configuration.

We provide technical support and are readily available via email, whatsup and telephone.

Feel free to contact us at - or - for any inquiries or assistance.

After placing an order, the flow and pressure can be fully adapted to the machine according to the customer's specific requirements.

--------------------------------------------------------------------------------------------------------------------------------------------------------------

Hydraulic, sectional valve Walvoil DPX 100 with compensation, full proportional

Technical specifications of default configuration:

Inlet section: 32GPM 120l/min - Pmax 300 bar 4351psi Power supply port: 3/4" BPS, tank return port: 3/4" BPS

1st Main Boom 60l/min 16GPM Anti shock valves 190/80 bar 2755/1305psi A+B closed, electro-hydraulic control on both sides with AMP-JPT or Deutsch connectors with hand lever

2nd Boom 60 l/min 16GPM Anti Shock valves 190/220 bar 2755/3190psi A+B closed, electro-hydraulic control on both sides with AMP-JPT or Deutsch connectors with hand lever

3rd Slewing 40 l/min 10GPM Anti Shock valves 200/200 bar 2900/2900psi A+B closed, electro-hydraulic control on both sides with AMP-JPT or Deutsch connectors with hand lever

4th Extension 80l/min 21GPM Anti Shock valve 140 bar/plugged bar 2030psi side A 4/3 center; A+B closed, electro-hydraulic control on both sides with AMP-JPT or Deutsch connectors with hand lever

5th Rotator 20 l/min 5GPM A+B closed, electro-hydraulic control on both sides with AMP-JPT or Deutsch connectors with hand lever

6th Grapple 60 l/min 16GPM A+B closed, electro-hydraulic control on both sides with AMP-JPT or Deutsch connectors with hand lever

7th Support Left Leg 20 l/min 5GPM A+B closed, electro-hydraulic control on both sides with AMP-JPT or Deutsch connectors with hand lever; Spool: 20L/min; No Anti-shock valves

8th Support Right Leg 20/min 5GPM A+B closed, electro-hydraulic control on both sides with AMP-JPT or Deutsch connectors with hand lever; Spool: 60L/min; No Anti-shock valves

Outlet section: with the possibility of combining valves, with bleed valve (LS relief), with pressure reducing valve. Control connection "V" and drainage connection "L" closed. Side connections "T1", "P1", "LS1" closed. DBV fixed and sealed to 175 bar at 90L/min .

--------------------------------------------------------

Scanreco G3 Canbus with Otto Joysticks:

--------------------------------------------------------

CANBus card for analog/digital inputs.

DESCRIPTION

MDCi is an electronic board with CANBus interface to

simulate 2 JC joysticks with 2 Otto joystick and push button dashboard.

The transmission has course immediately after the turning on of the

electronic card.

FEATURES

- supply voltage from 10 to 30 Vdc

- CAN V2.0B communication bus

- 120 Ohm inner terminator not present in this version

- 2 diagnostic LEDs (red and green)

- firmware updatable by integrated serial port

SIGNALS

Red LED flashing one time: short circuit error on the +5V stabilized output

Red LED flashing two times: one of the analog inputs has been found not at rest position during the turning on, this

input is blocked until a reset.

Green LED On: the electronic card is working correctly.

The green LED flashes one time every time an input (analog or on/off) change status.

MDCi contro unit for OTTO joystick interface
and button panel for Forest Crane
Mounting version: X1
Firmware: mdc_P5_01.hex
Cfg file: mdc_P5_01.cfg

--------------------------------------------------------

Otto Joysticks NOTE:
to have the cable L = 1.5m it is necessary to
- make the joystick / cable connections 7x0.75mmq by removing the
original connector
- put the corrugated sheath and fix it to the bottom of the joystick (see photo)
- connect the 7x0.75 cable to the Deutsch 6-pin female connector
to male contacts

--------------------------------------------------------

STUi Technical Specifications:

Power Supply Voltage : 10Vdc÷30Vdc (inner 5x20 8A fuse type F8A)

Current absorpion : 300mA + load outputs (max 7.5A)

Wroking Temperature Range : -20 ÷+ 70 C

Supply for external poterntiometers: +5V - max current 50mA

PWM minimum current range : from 100 to 2500 mA

PweM maximum current range: from 100 to 2500mA

PWM frequency : 50-60-70-85-100-125-150-200-250-300 Hz

Analog inputs impedance: 11 KOhm towards 2.5V

Overlall dimensions with connector mounted: 256x210x45mm

Drill interasis : 242x142mm (n. 4 holes of 6mm diameter)


--------------------------------------------------------

Remote Radio Control Scanreco:

-1–8 linear levers or 1–4 joysticks. » Various toggle switches, pushbuttons and rotary switches.

- Operator feedback by:

- LEDs (light emitting diodes)

- Monochrome display 2.5" with 128 x64 px

- Stop function in accordance with EN ISO 13849-1 cat. 3, PL d.

- Cable control: Standard length 10 meters / ~33 ft

- Frequency bands: 433–434, 902–928 MHz & 2.4 GHz (other frequencies available on request).

- Operating range >100m / >

~330 ft.

» Operational temperature: –20°C to +70°C / ~–4°F to +160°F.

- Protection category: IP65. » Dimensions: (WxHxD): 350 x160 x190 mm / ~13.78 x6.30 x7.48 in (w/o color display).

» Weight: 1.9–2.6 kg / ~4.2–5.7 lbs. including battery

--------------------------------------------------------

The kit works with cranes from Palfinger, Hiab, Palms, Kesla, Fassi, Liebherr etc.

A leírás lefordítása